SKIDOO 900T & 900R TURBO UPGRADE KIT

 


This is a high level guide for the installation of our upgraded turbo kit on Skidoo 900T & 900R snowmobiles. Installation of these systems can be done with standard tools, but assumes reasonnable mechanical knowledge by the person doing the work. Do not attempt to install these systems if you have no experience undertaking similar projects of moderate complexity.

This guide assumes all original components to be upgraded have already been dissassembled and removed from the vehicle. Everything should be at a stage where the installation of the new systems can begin. In an effort to simplify the use of this guide, sub-sections all relate to a specific component of the install.

Let's begin by suggesting an installation sequence. It should ideally be as follows:

  1. Turbo header
    • Use the supplied 8mm studs in replacement of the original header bolts. However, these will need to be installed so that they are long enough to compensate for the thickness of the header and the lock nuts. Ensure to have one full thread after the lock nut. Apply red loctite on the threads going into the cylinder head and screw in just enough to get the proper lenght mentionned above, Once you have your lenght correct, let the loctite set for a few hours before attempting to install the nuts.
    • Make sure the turbo header fits easily into the 9 cylinder head studs. If something feels tight, simply take the time to lighlty file the header bolt holes to ensure a better fit -- it may be the stainless flange has somewhat twisted a little during the weld process. In any case, do not worry about flange straightness and/or flatness as this was machined as the last step.
    • install the header and torque properly
  2. Wastegate
    • Position the wastegate on the header and leave the clamp loose while you will be adjusting the final positioning of the wastegate downpipe.
    • Install all fittings on wastegate. Note that there are 2 sections we will refer too when describing where each fitting should go: the top section of the wastegate and the bottom section. The top section is the one that only has 2 ports for installing fittings. The bottom section is the one with 5 ports
    • Configuration of wastegate fittings should be:
      • Top section: one of the 2 ports should be plugged and the other one should be left open. It does not matter which one is which.
      • Bottom section: the 2 H20 ports should be left open and no fittings should be used. 2 of the 3 remaining ports should be plugged and 1 should be used for the boost controller signal. It is on that port the a barb fitting with banjo bolt provided with the wastegate should be installed. Here again, it does not matter which of the 3 ports is used for the boost controller connection. However, keep in mind it is always best practice to use a port further aways from extreme radiant heat.
  3. Wastegate downpipe
    • The wastegate downpipe requires cutting a 2 inch hole at the bottom of the bellypan. Use a holesaw for this. Make sure you position a pilot hole before you cut. Pilot hole should be 1.5" from end of bulkhead where the bottom flat floor of the bellypan turns into a 90* degree. Please refer to the installation picture library to understand exactly where your pilot hole should be. Measure twice & cut once as the old saying goes.
    • Once the downpipe exit hole is cut, simply position and clock your wastegate downpipe as the installation picture library suggests. Ensure there is clearance all around the wastegate downpipe and it does not rub against the frame.
    • Once everything is properly aligned, simply tighten the wastegate clamps
  4. Turbocharger
    • If your turbocharger was purchased from Precision Sports, then it comes ready to install. It is properly clocked and all fittings are already attached to it.
    • Install the turbo on the header flange and leave the clamp loose enough so the turbo can be clocked on the header flange.
  5. Turbocharger oil lines
    • Start with the oil drain. Connect the small section (around 3" long) of 5/8" rubber hose with a 90* degree brass elbow on one end. Install this hose onto the turbo drain tube. Install so that the 90* degree brass fitting points towards the rear of the snowmobile. That brass fitting should nw connect to the stock oil drain hose. The stock oil drain hose should be routed under the frame section which is above the bellypan floor. Refer to picture 3 to visualize where the stock oil drain hose should be routed for proper connection with the turbo oil drain fitting. Once everything is installed properly, simply install clamps on the assembly (2 required)
    • The oil supply line is the 18" long stainless braided hose provided in your kit. It connects to the -4an  oil feed restrictor fitting already installed on the turbocharger on one end and to the stock oil feed port on the engine. You will need to disgard the stock oil supply line. Keep the 2 stock copper crush washers used on the engine and reuse them along with the banjo bolt with the banjo -4an fitting supplied with your kit. You are now ready to connect the engine end of the oil supply line.
  6. Turbocharger outlet
    • If using the stock intercooler, connect the stock rubber tube to the turbocharger outlet. This will be difficult as the outlet size of the biigger turbo is larger than on the stock turbo. Use a liberal amount of dishwasher soap to lubricate the inside of the rubber hose slipping into the turbo outlet section. Apply force, twist and push -- it will go.
    • If using our custom intercooler, then simply connect the turbocharger outler to the intercooler using the aluminum tube and silicone connectors supplied with your kit. Refer to the installation picture library.
  7. Turbocharger air inlet
    • Install the air inlet 90* degree 3 inch rubber adaptor on the turbocharger inlet. Do not tighten anything at the stage. Do the same for the air filter provided with your kit.
  8. Intercooler
    • This is a straight forward install. Simply install the intercooler the same way the stock intercooler is installed. You will note there is a 1/8NPT female ports on the intercooler -- This port is normally used to connect to the boost controller as the pressure feed signal. If not used, just plug that top port.
  9. Turbocharger exhaust downpipes and muffler
    • Your kit is provided with a custom exhaust downpipe which connect the turbo to the muffler. The important thing when installing this downpipe is to ensure it is properly clocked. When clocked in the intended position, the exhaust seals align properly and the springs do not contact with the oil filter housing. Take your time to play with the alignment until you are satisfied. This is an area where many customer go wrong. Time and patience to get everything properly lined up here is key. Please refer to the install pictures.
  10. Aluminum intake (optional on some applications)
    • If your kit comes with our custom aluminum intake manifold, then that manifold replaces the stock plastic unit. The throttle body mounts directly on the manifold and a o-ring is supplied with the intake to ensure a leak free seal between the throttle body and the intake manifold 4 bolt flange. Simply install that o-ring between the two mating surfaces. The intake flange that bolts to the cylinder head also requires to reuse the stock Skidoo seals that were on the plastic manifold. Install these seals into the flange grooves and bolt the manifold to the head. At this stage, and before bolting the manifold to the head, it is a good idea to have the 3 injectors and fuel rail already installed on the intake.
    • The aluminum intake will require routing the throttle body and MAP wiring between cylinder 1 and cylinder 2 runners. This provides more wiring lenght to the relocated throttle body. Injectors should ideally be rotated 180* degrees from their normal position so that connectors face the rear of the engine on 900R models. This also allows for greater clearance for electrical connections. You will also need to relocate the fuse box as it will no longer install at the stock location. Remove the metal bracket on the fuse box and use a few zip-ties to secure the fuse box in a convenient location giving reasonnable access to remove the cover to service the relays and fuses should the need for this arise in the future.
    • The clutch side of the aluminum intake as the provision to install your map sensor. Simply install the map sensor in that location.
    • The coolant bottle side of the aluminum intake has a 1/8npt pressure port. That port is used to connect to a Blow Off Valve or a boost gauge if so equipped. If none of these are installed on the snowmobile, simply plug that port closed.
  11. Blow Off Valve (optional on some applications)
    • If your kit comes with the optional Blow Off Valve, then simply install the BOV on the aluminum charge tube provided with your kit. The BOV reference vacuum line should connect to the intake pressure port on the coolant bottle end of the intake plenum where there is a 1/8npt pressure port to install a barb fitting on which the reference line is installed.

We hope the above will be useful in helping you install your new upgraded turbo system. Please contact us for any additional information you may need during your installation.