SKIDOO 900T & 900R MaxxECU INSTALLATION

 


Please read carefully

This guide describes the key features, installation and operation of your MaxxECU standalone engine management system for all 2019-2024 Skidoo 900T and 900R snowmobiles.

Please take the time to read this guide carefully in order to ensure a successful installation and proper operation. Failure to install your ECU properly will create operation problems and issues.

Your MaxxECU engine management system is a highly sophisticated ECU designed and calibrated to replicate factory engine and chassis functions. It is compatible with all Skidoo and Lynx 900T & 900R models manufactured between 2019 to 2024, including active suspension, air ride suspension and Expedition models.

Key supported factory options are:

  • Analog and digital dash clusters, including Deluxe models with rotary knob.

  • Electric reverse

  • Active and air ride suspension

  • Auxiliary cooling fan

  • Electronic throttle control

MaxxECU systems are the only standalone solutions currently available for 900T snowmobiles. Original development by Precision Sports goes back to 2019 when the first 900T’s were introduced on the market. It is worth noting that all 900T MaxxECU systems can easily be upgraded to 900R specs with the purchase of a compatible adaptor loom. In other words, they remain transportable to more recent 900R snowmobiles.

Calibrations are available for higher flow injectors as well as the factory 900R injectors. Precision Sports recommend upgrading to high flow injectors to take full benefit of the system, regardless of what turbocharger is used. Staged injection is also available for use with higher octane fuel. A MaxxECU engine management system can manage whatever power output is supported by the hardware installed on the vehicle and the motor itself. Engine management is no longer a limiting factor as it is the case with production factory ECU’s.

Key features of the 900T & 900R MaxxECU engine management system include:

  • Closed loop fuel, knock and boost control

  • Datalogging

  • Launch control from a dead stop

  • Rolling launch control

  • Automatic engine cranking at the simple push of the start button

  • Automatic fuel adaption and self main efficiency table correcting mode

  • Lean condition engine cut protection

  • Overheat engine protection

  • Over boost protection that resets itself on the fly

  • ETB fault protection triggering rpm limit below clutch engagement for greater safety

  • Check Engine Light reset function from the handle bars

  • Integrated 4bar MAP sensor

  • Integrated Barometric sensor

  • Over RPM ETB governing function

  • Configurable fuel, timing and boost maps

  • Bluetooth Android communication

  • Bluetooth vehicle immobilizer and theft prevention

  • Encrypted calibration protection

  • Closed loop idle control

  • High EGT engine cut protection (when optional EGT probes are installed)

  • Multi-calibration and performance mode – ECO, Standard and Sport

  • Staged injection capability for up to 6 injectors

  • User defined ECU power on/hold time delay following engine shutdown

  • Speedometer calibration allowing high accuracy regardless of track driver tooth count

  • Configurable cooling fan start & stop parameters

  • Barometric compensation

  • External ignition driving for increased spark energy

  • High capacity fuel pump relay supporting most aftermarket fuel pump

  • End user programmable Outgoing Can Bus messaging

  • Pre-defined injector calibration library

  • USB computer interface

  • Windows compatible ECU Manager software

  • Windows compatible datalog editor

INSTALLATION

Customers using our high flow custom intercooler or upgraded turbo kit should install the ECU on the intercooler. There are 2 allen head bolts on the clutch side of the intercooler to secure the ECU on the intercooler.

Customer who are using the stock intercooler can install the ECU at the front of the snowmobile using the mounting plate supplied with their kit. This mounting plate is compatible on all 2022-2023 900T and 900R snowmobiles. It is not compatible on 2024 snowmobiles because of colling fan interference. The mounting plate requires no drilling and mounts the ECU using the 4 supplied zip ties. When using the mounting plate, you need to use 4 plastic washers between the ECU and the mounting plate. This is done to create a gap which isolates the ECU from the plate and prevents potential moisture and galvanic corrosion over time. We recommended you install the ECU antenna before you finalize the physical mounting of the intercooler -- access is limited afterward.

Once the ECU is mounted, it is time to install the loom.

Skidoo 900T:

The 900T loom connects to the MaxxECU on one end and to the factory Skidoo ECU connectors on the other end. It can only go one way on the factory Skidoo connectors. Ensure you do not force the connectors while installing as you may damage the pins. Damaged pins are not covered under any warranty, this is your responsibility. Every loom has been quality verified for pin integrity prior to shipping.

Skidoo 900R:

Skidoo 900R snowmobiles use a custom integrated circuit junction board to interface between the factory loom and the MaxxECU loom. This junction board allows to connect the factory ECU connectors on one end and the MaxxECU single 48pin connector on the other end. Installation is simple but extra care should be taken when inserting the connectors to prevent damage to the pins – do not force the connectors. When everything is properly aligned, connectors go in easily and locking is effortless. All junction box connectors go through a detailed quality inspection before they are shipped. There is no warranty coverage when pins are bent due to improper installation.

The junction box mounts on the 1” aluminum frame tube as per the attached picture. Install on the aluminum tube and secure with the 2 tie wraps supplied with your kit.

Now is the time to secure the loom with tie wraps and ensure there will be no damage due to rubbing or chaffing. Take your time here and do a quality install. Your loom has been designed so that it is long enough to allow for easy installation – take your time here as preventing chaffing and loom heat damage are key to a successful installation.

Once the above is done, you will need to make a few extra connections:

  • Connect the Ground wire on the MaxxECU loom to the Engine. We suggest using either an oil cooler or an intake bolt for good grounding. Do not connect on any valve cover bolts as they do not provide a good grounding source due to the rubber gasket and seals.

  • Connect your wideband O2 sensor to the MaxxECU connector used for that purpose.

  • 900R only: a distinct connector is used for the speed sensor because the factory connection uses a chassis ground for that sensor. This increases the likelihood of electrical noise and speed sensing errors. Our system uses a floating ground for that sensor which is always better when vehicle speed values are used as an ECU input channel for launch control. Simply disconnect the factory speed sensor connector from the chaincase and connect the speed sensor 3 pin connector which is part of your MaxxECU loom. Secure the factory speed sensor connector with a tie wrap since it is not used with your MaxxECU system.

Optional: For customers using our Auxiliary Race Fuel Tank system, there are 2 additional connections:

  • Connect the 4 pin connector on the MaxxECU loom to the Auxiliary fuel injector loom

  • Connect the 2 pin connector from the MaxxECU loom to the mating connector supplied on your Auxiliary Fuel Tank loom.

At this stage you are ready to install your USB cable on your ECU. We recommend a permanent installation which will allow an easy and convenient connection to a laptop computer without having to remove the front end of the snowmobile every time. The suggested connection method is as follows:

  • Insert the suitable USB cable end into the USB socket on the ECU.

  • Route the USB cable so that it can be eventually stored in the glove box behind the windshield or bundled near the reverse relay at the back of the muffler and near the factory fuse box.. Whenever connecting to a laptop is required, it will simply be a matter of retrieving the cable.

  • When using our Auxiliary Fuel Tank System, you will then need to use the internal 4 bar MAP sensor on the MaxxECU. Connect the female port at the front of the ECU to the intake manifold vacuum port using the supplied nylon tubing. Take extra precaution to route the nylon tube so that it does not melt on hot engine/exhaust parts or get damaged by chaffing on sharp metal parts. You do not need to use the internal MAP sensor when operating the engine at boost levels supported be the factory MAP sensor (300kpa maximum).

 

INITIAL THROTTLE LEVER AND ETB CALIBRATION

Your MaxxECU is shipped with a base calibration with reasonable throttle lever and ETB sensor settings. However, these settings may not always be perfect for all snowmobiles. Normal idle speed is 1600rpm +50rpm. Idles should be smooth and consistent

If you observe a different idle speed than the above or if the idle is often erratic when the engine is at normal operating temperature, then we suggest taking the time to reset these settings so that they are calibrated for your vehicle. This is not something that can be done by end users - parameters are locked for safety. Contact Precision Sports to get these sensors properly calibrated and matched to your snowmobile. You will need to have previously downloaded a free version of TeamViewer on your computer and have access to an internet connection near your snowmobile.

2022-2024 Wiring Loom

 

2022-2024 Junction Board

 

2022-2023 ECU Mounting Support (Does not fit 2024 900R)

 

2022-2023 ECU Plastic Washer Spacers

 

2022-2024 Junction Board Mounting Location

 

2019-2023 ECU Support Mounting Location

 

2019-2024 ECU Mounting on Precision Sports Intercooler

 

2024 Suggested ECU Mounting Location