SKIDOO 900R MAXXECU OPERATION |
Skidoo 2022-2025 900R MaxxECU operation
The following are basic operator instructions for all 2022-2025 Skidoo 900R MaxxECU systems calibrated after November 15, 2023. Systems calibrated and shipped prior to November 1st, 2024 may have different operating features in which case the following instructions do not apply. MaxxECU systems for 2019-2022 Skidoo 900T snowmobiles essentially have the same operation principles.
- ENGINE CRANKING & STARTUP: all MaxxECU systems feature an automatic engine start function similar to what is found in most modern cars. The ECU is configured to crank and automatically start the engine after a brief push of the the "start button". Cranking time is set to a maximum duration of 3 seconds for every startup attempt. It is also possible to press and hold the start button the force longer cranking time.
- REVERSE AND FORWARD OPERATION: shifting between forward and reverse is done the same way BRP configured all 900R with electric reverse. However, when reverse is engaged, SPORT mode will be disabled and ECO mode will be enabled for smoother operation. STANDARD or SPORT modes are enabled again automatically once the transmission shifts back into forward. The "start button" is used for reverse/forward operation. Vehicle speed should be less than 3kmh or 1.9mph and engine speed lower than 1900rpm. The ECU automatically reverts back to forward if the engine is turned off while the transmission is still in reverse.
- EXTENDED ECU POWER ON TIME: This function is useful when the engine is not running and ECU power is required to download larger log files and/or more time is required to configure the dashboard. To enable this function, the ECU must already be powered on. The "kill switch" must be in the run position and the "brake lever" should be locked. The ECU remains powered up for 10 minutes when these 2 conditions are met. After 10 minutes, the ECU shuts down to avoid draining the battery. This function can be disabled at any point by releasing the "brake lever" or by putting the "kill switch" in the off position.
-
DATALOGGING: MaxxECU systems are configured for selective datalogging recording. This means data is not recorded on an ongoing basis, but only when relevant and/or required. Enabling selective datalog recording is a simple:
- To activate datalogging when the engine is turned off, press the "throttle lever" (fully to the bars). The ECU will start datalogging for a fixed period of 30 seconds.
- ECU datalogging also automatically starts whenever a launch control function is active or throttle lever position is greater than 90% open. Log recordings in these conditions have a fixed duration of 30 seconds.
-
LAUNCH CONTROL: MaxxECU systems feauture two different launch modes:
- From a dead stop. Typical boost pressure when launching from a dead stop is around 6-8psi. vehicle speed must be 0kmh/mph. Vehicle mode should be in SPORT. Brake lever should be pressed for a continuous minimum of 3 seconds without releasing before accelerating the engine. Throttle lever should be gradually increased until it reaches WOT. Releasing the brake lever will launch the vehicle. Typical pre-launch duration is around 2-4 seconds. We recommend not to exceed 4 seconds to avoid overheating the turbocharger.
- From a rolling start. Typical boost pressure when launching from a rolling start is around 16-20psi. Vehicle speed must be above 8kmh/5mph. Vehicle mode should be in SPORT.
- 2019-2023 snowmobiles: Vehicle speed should be above 8km/h (5mph) and throttle position should be above 8%. The "start switch" should be pressed and held pressed during pre-launch for all 2019-2023 snowmobiles. The "throttle lever" should be fully pressed while the "start button" is pressed. Releasing the "start button" will launch the vehicle. Typical pre-launch duration is around 2 seconds.
- 2024 snowmobiles: Vehicle speed should be above 8km/h (5mph) and throttle position should be above 8%. The "brake lever" should be lightly pressed for a minimum of 2 seconds before the rolling launch function is enabled. Once enabled, the "throttle lever" should be fully pressed while the "brake lever" is still lightly pressed. Releasing the "brake lever" will launch the vehicle. Typical pre-launch duration is around 2 seconds.
-
SELECTING ENGINE PERFORMANCE MODES: MaxxECU systems support the 3 original factory engine performance modes (Eco, Standard, Sport) on all Skidoo 900T & 900R from 2019 to 2025 . These modes are fully functional and displayed on the dash.
- Selection of the 3 performance modes is identical to stock on all 2019-2023 snowmobiles equipped with the "mode selector switch" on the console.
- Mode selection for all 2024-2025 models remains the same as stock.
* * * * *
All previous Skidoo 2022-2023 900R MaxxECU systems can be upgraded to the above specifications and/or can also be configured to be compatible with the new 2024-2025 dashboards. Email Precision Sports for more information about this process info@precisionsports.ca





